Can anyone comment on RSP redundancy with SSO mode?
Craps 32 across. Although graceful deactivation of a SIP is preferred using the hw-module slot stop command, the Cisco Aggregation Services Router 1000 Series do support removal of the SIP without deactivating it first. If you plan to remove a SIP, you can deactivate the SIP first, using the hw-module slot stop command in global configuration mode. Hw-module slot (7300) hw-module slot (7600) hw-module slot (ASR 1000 Series). Casino redwood falls minnesota. Poker house netflix. This casino No Hw Module Slot 1 Oversubscription table game is just as exciting to play online. Roulette requires no skill to play, although it is helpful to learn the best bets to make.
- Hw Module Slot X Oversubscription, winstar world casino and resort map, 15 slot backpack aura kingdom, empirical rule games.
- Hw Module Slot R1 Reload, quick hits slots apk, online casinos uk players, betsafe poker where is the hand history located.
I have a test 7507 with rsp-k4pv-mz.120-32.S8.bin on both RSP2s. I've done
this:
service single-slot-reload-enable
redundancy
no keepalive-enable
mode sso
And it doesn't seem to ever sync the slave
ranttest#show red
Redundant System Information :
------------------------------
Available system uptime = 14 minutes, 49 seconds
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = hsa
Maintenance Mode = Disabled
Communications = Down Reason: Simplex mode
Current Processor Information :
-------------------------------
Active Location = slot 2
Current Software state = ACTIVE
Uptime in current state = 13 minutes, 24 seconds
Image Version = Cisco Internetwork Operating System
Software
IOS (tm) RSP Software (RSP-K4PV-M), Version 12.0(32)S8, RELEASE SOFTWARE
(fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Mon 20-Aug-07 16:34 by leccese
Hw-module Slot X Oversubscription
BOOT =
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Peer (slot: 3) information is not available because it is in 'DISABLED'
state
ranttest#redundancy force-switchover
Cannot perform switchover until the standby is fully initialized.
The box is up, its got two OSPF adjacencies, maybe a hundred routes - its
not doing anything fancy, so I'm kind of stuck here. The production target
is 7507s /w RSP4s, the same OSPF, and about 180k routes via BGP. Any idea
Hw-module Slot 1 Oversubscription
what might be wrong here?
_______________________________________________
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = hsa
Maintenance Mode = Disabled
Communications = Down Reason: Simplex mode
Current Processor Information :
-------------------------------
Active Location = slot 2
Current Software state = ACTIVE
Uptime in current state = 13 minutes, 24 seconds
Image Version = Cisco Internetwork Operating System
Software
IOS (tm) RSP Software (RSP-K4PV-M), Version 12.0(32)S8, RELEASE SOFTWARE
(fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Mon 20-Aug-07 16:34 by leccese
Hw-module Slot X Oversubscription
BOOT =
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Peer (slot: 3) information is not available because it is in 'DISABLED'
state
ranttest#redundancy force-switchover
Cannot perform switchover until the standby is fully initialized.
The box is up, its got two OSPF adjacencies, maybe a hundred routes - its
not doing anything fancy, so I'm kind of stuck here. The production target
is 7507s /w RSP4s, the same OSPF, and about 180k routes via BGP. Any idea
Hw-module Slot 1 Oversubscription
what might be wrong here?
_______________________________________________
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp